RECMAD03
receiver for roller doors
receiver enjoy R4 to be used with mechanical or electronic limit switch motors
Receiver with 433.92 MHz frequency, for managing a mechanical motor or an electronic motor wirelessly. Compatible with all other enjoy R4 products
It is made in a container with IP54, so it can be installed outside the home, garage, ... Being a product to be used with domestic roller doors, this receiver admits some specific products for this use, as photocells or safety edge, key psuh-button, courtesy light, big torque motors, ...
It is made in a container with IP54, so it can be installed outside the home, garage, ... Being a product to be used with domestic roller doors, this receiver admits some specific products for this use, as photocells or safety edge, key psuh-button, courtesy light, big torque motors, ...
- Frequency 433.92 MHz. Compatible with enjoy R4
- To be used with motors up to 1600 W
- Programming the first remote control when receiver is powered. All the other remotes can be memorized without the need to manipulate the receiver or power
- RECMAD03 admits up to 15 remotes controls
- Internal connection strip, to facilitate motor and power wiring in
- Possibility of connecting courtesy light
- Possibility of connecting the internal push-button plus external key-switch
- Possibility of connection of interior courtesy light and external siren
- Option safety stop by safety edge or photocells
- 4 operating modes: dead man; automatic; 180 seconds working time; using a single button from remote
Operating type:
Individual operating mode (1 receiver RECMAD03 for 1 roller shutterEMSR4K1):
Attention:
- It is not allow to connect more than 1 mechanical motor directly to the receiver RECMAD03
- If you want to convert several mechanical motors into radio products, you must use a receiver for each motor
- In the case of ELM motors, if they are going to work as a group, several motors can be connected into the receiver, with the limit that the sum of the watts (W) of these motors does not exceed 1600w
Diagram of accessories admitted with this receiver:
1) Motor JE50FMM 2) Receiver RECMAD03 3) Push-button from inside 4) Safey edge 5) photocells 6) Interior courtesy light 7) Outdoor siren 8) External key-switch 9) Remote control EMSR4K1
Safety stop option "safety edge":
Receiver RECMAD03 is compatible with the safety stop system for roller blinds better known as "safety edge" This system is made up of 3 elements:
As soon as the rubber is pressed by an object, the transmitter unit sends the order to stop the RECMAD03 receiver and it automatically stops the motor (or reverses the maneuver to release said object), avoiding further damage to both the roller shutter and the object that caused the alert:
- Transmitter unit. It receives the order by the rubber detector of the 2-wire terminal, and sends the stop order to the RECMAD03 receiver via radio under the freq. 433.92MHz
- Detector rubber for terminal
- Magnetic connector to deactivate the sensor when it reaches the lower point
As soon as the rubber is pressed by an object, the transmitter unit sends the order to stop the RECMAD03 receiver and it automatically stops the motor (or reverses the maneuver to release said object), avoiding further damage to both the roller shutter and the object that caused the alert:
⚠ New:
product available during the second half 2020
product available during the second half 2020
Option safety stop "photocells":
Receiver RECMAD03 is compatible with the safety stop system for roller shutters through a pair of photocells or a photocell and mirror:
As soon as the light beam is cut by an object, the RECMAD03 receiver automatically stops the motor (or reverses the maneuver to free the object), avoiding further damage to both the roller shutter and the object that caused the alert:
As soon as the light beam is cut by an object, the RECMAD03 receiver automatically stops the motor (or reverses the maneuver to free the object), avoiding further damage to both the roller shutter and the object that caused the alert:
Techcnical data:
| Product Code | RECMAD03 |
| Input power | 230V-50Hz |
| Output power | 230V-50Hz |
| Watts capacity | 1600W |
| Protection rating | IP54 |
| Product Dimensions | 168 x 126 x 67 mm |
What products can I use it with?:
- Receiver RECMAD03, is compatible with all mechanical and electronic motors from our series JE40, JE50, JE60 and JE100
- It is compatible with all enjoy R4 remotes controls: Titamium, Steel, Murus, ...
- Enjoy R4 works with frequency 433.92 MHz and has the rolling code system to protect the signal
